DXC Conversion Unit | Performance | Specifications

DXC Conversion Unit (refrigerated) CONVERTS The DXC Series Refrigerated Conversion by Kleen-Rite CONVERTS your Vented Dry-to-Dry to a NEW closed loop refrigerated Dry-to-Dry process. COMPILES The DXC Series MEETS E.P.A. rules under the Clean-Air Act, including California and New York regulations. SAVES MONEY The DXC Series SAVES you MONEY. Why buy a new refrigerated Dry-to-Dry unit when YOU can convert your existing open Dry-to-Dry for a fraction of the cost. You'll meet E.P.A. regulations, extend the life of your old vented Dry-to-Dry, increase solvent mileage, have cooler solvent and less wrinkling of clothes.

DXC Conversion

KR-DXC Coil Conversion:
The Coil Package comes pre-assembled to a new matching reclamation head cover and includes the expansion valve, self sealing quick connect fittings and proper charged R-22. With the self-sealing connections the Coil Assembly may be safely removed for cleaning without loss of refrigerant.

KR-DXC Condenser Unit:
Compact design can be floor, wall or ceiling mounted. This Packaged Unit comes complete with pre-charge of R-22, sight glass, filter dryer, accumulator and self-sealing quick connect couplings for easy installation.

KR-DXC Line Sets:
Liquid and suction lines are pre-charged with environmentally approved R-22. These Line Sets are insulated and ready to install by using the simple self-sealing quick connect couplings. Line Sets may be ordered in custom lengths at no extra charge up to 40ft maximum.

DXC
Setting the Standards for Performance

Cabinetry:
Constructed of galvanized steel and baked powder paint panels.

Compressor:
Thermally protected water-cooled and carries a one-year warranty.

Digital Microprocessor Controller:
Accurately indicates and monitors the DXC Conversion Coil exit temperature for E.P.A. compliance.

Refrigeration Connections:
Simple quick connect coupling eliminates the possibility of refrigerant loss in line connections. No need to evacuate or charge the system. Requires only two wrenches for installation.

Air Switch:
Synchronizes the Dry-to-Dry Cycle with the DXC Unit. Simplifies installation by eliminating electrical control wiring.

Water Modulating Valve:
Regulates water flow to condenser unit to cool refrigerant and conserve water usage.

Sensor Protection:
Microprocessor automatically shuts down unit in case of temperature sensor failure or in the event of freezing conditions.

Dual Pressure Switch:
Shuts down unit in case of high or low refrigerant pressures.

Refrigeration Solenoid:
Pumps down refrigerant to receiver to protect compressor.

Manual Reset:
Shuts down unit in case of high pressure or lack of cooling water to condenser unit.

DXC Specifications

Refrigeration	DXC-4	DXC-6
Refrigerant	R-22	R-22
Liquid Line - Provided by KR*	3/8"	3/8"
Suction Line - Provided by KR*	5/8"	7/8"
Water	DXC-4	DXC-6
Inlet (female pipe thread)	3/4"	3/4"
Outlet (female pipe thread)	3/4"	3/4"
Flowrate Required (GPM)	2	4
Electrical	DXC-4	DXC-6
Condensing-Unit Type	Water Cooled	Water Cooled
Horsepower Rating	4	6
Phase	1	3
Volts	208/230	208/230
Hertz	50 or 60	50 or 60
Maximum Fuse Size	30	45
Minimum Circuit Ampacity	17.9	26.8
*Standard Length 25 feet. Line Sets may be ordered in custom lengths at no extra charge.

Send mail with questions or comments about this web site.
Copyright © 2006 Kleen-Rite, Member of the International Fabric-Care Institute.